Hi @pcchrister, can you send a short video of what you are seeing on your WiFi screen to support@mosaicmfg.com? We'll look into this for you, thank you.
Hi @ladakhan, it sounds like you are looking to print in accessory mode. While you are working within the project, the top-right panel has the Palette options available. Please check that accessory mode is toggled on, and that the combined model has more than one color used: mm3d.co/calibration-maf-print
Hi @rnunez24, the splice core can is a DC brushless fan, rated 12 VDC, rated 0.21 A. Apologies, I don't have the CFM info available, but I hope this helps.
Hello, the LO saved to the printer profile on Palette represents the distance from the tube clip to the printer nozzle (basically any additional distance the filament must travel once the filament exits the outgoing tube). There is a bowden tube length setting in Canvas' printer profile settings, but this wouldn't affect the amount of filament created at the beginning. Once the filament coming out of the tube is engaged by the extruder, the next screen on Palette should prompt a number of millimeters left to load (with or without smartloading). If the amount being asked to load is too short and will not bring enough filament to the nozzle, an increase in the LO on Palette would be required.
With Palette 3, the outgoing tube length does not need to be added to the loading offset. For a direct drive printer, the LO should be from the tube clip to the nozzle (length of hot end). For bowden printers, the LO should start from the tube clip on the extruder + bowden tubing + hot end. You can learn more about this here, and please also let us know the printer you are using.
Hi @lukerobertsorth, would you be able to try running an IP scan and see if the hub displays with its IP address? The hub should appear as abcd-ch-canvas-hub under the manufacturer. The IP address can then be copied and pasted into the browser to connect to Octoprint.
Hi @crusher17, the specifications for both of these printers look to be compatible. I would recommend creating a printer profile in Canvas3d.io to become familiar with slicing for Palette, and to test print quality in single color.
Hi @althd0656, when you go to Network Connection and enter the password for your home/local WiFi network, it is normal that during the rebooting stage the hub will disconnect from its hotspot and then switch over to the network you entered the password for.
Hi @micchan, to answer your questions: 1) P3P currently supports PLA for multispool mode. 2) Selecting splice tuning for multispool mode is now available in P3P. Please see our firmware update here.
Hi @pcchrister, can you send a short video of what you are seeing on your WiFi screen to support@mosaicmfg.com? We'll look into this for you, thank you.
Hi @ladakhan, it sounds like you are looking to print in accessory mode. While you are working within the project, the top-right panel has the Palette options available. Please check that accessory mode is toggled on, and that the combined model has more than one color used: mm3d.co/calibration-maf-print
Hi @rnunez24, the splice core can is a DC brushless fan, rated 12 VDC, rated 0.21 A. Apologies, I don't have the CFM info available, but I hope this helps.
Hello, the LO saved to the printer profile on Palette represents the distance from the tube clip to the printer nozzle (basically any additional distance the filament must travel once the filament exits the outgoing tube). There is a bowden tube length setting in Canvas' printer profile settings, but this wouldn't affect the amount of filament created at the beginning. Once the filament coming out of the tube is engaged by the extruder, the next screen on Palette should prompt a number of millimeters left to load (with or without smartloading). If the amount being asked to load is too short and will not bring enough filament to the nozzle, an increase in the LO on Palette would be required.
With Palette 3, the outgoing tube length does not need to be added to the loading offset. For a direct drive printer, the LO should be from the tube clip to the nozzle (length of hot end). For bowden printers, the LO should start from the tube clip on the extruder + bowden tubing + hot end. You can learn more about this here, and please also let us know the printer you are using.
Hi @lukerobertsorth, would you be able to try running an IP scan and see if the hub displays with its IP address? The hub should appear as abcd-ch-canvas-hub under the manufacturer. The IP address can then be copied and pasted into the browser to connect to Octoprint.
Hi @crusher17, the specifications for both of these printers look to be compatible. I would recommend creating a printer profile in Canvas3d.io to become familiar with slicing for Palette, and to test print quality in single color.
Hi @althd0656, when you go to Network Connection and enter the password for your home/local WiFi network, it is normal that during the rebooting stage the hub will disconnect from its hotspot and then switch over to the network you entered the password for.
Hi @micchan, yes, ABS and ASA are compatible.
Hi @micchan, to answer your questions: 1) P3P currently supports PLA for multispool mode. 2) Selecting splice tuning for multispool mode is now available in P3P. Please see our firmware update here.
Page 1 of 3
Next